General

Prev Next
  • Published on Mar 13, 2024
On the NVR UI. Go to the Security and choose system service 2. Under system service, choose HTTPS, enable the function. 3. Choose certificate management Download the certificate 5. Install certificate 6. make sure t...
  • Updated on Feb 13, 2022
  • Published on Feb 11, 2022
How To Enable H.264 Description If you have a H.265 Camera and a H.264 recorder, you won't be able to view your feed! To resolve this issue please follow the steps below to set your IP Camera to the H.264 codec. Prerequisites H.265 IP Came...
  • Published on Feb 11, 2022
You can find these information from here: https://www.dahuasecurity.com/support/downloadCenter/softwares?child=3
  • Published on Feb 11, 2022
You can go to the web interface of that camera to reset your camera: follow the steps: Setting -> System -> default -> factory default
  • Published on Feb 11, 2022
If you are looking for the software for Dahua recorder or Dahua Access Control, You can go to our website to download SmartPSS/ ASC2204C(SmartPSS): https://www.ametagroup.com/software If you are looking for the software for Dahua configurat...
  • Published on Feb 11, 2022
You have two ways to do that: 1.You can use switch 820 to change the video type of camera: You can go to the OSD Menu to switch the channel type Step 1: Go to Main Menu -> PTZ control Step 2: Click on the arrow: Step 3: Cl...
  • Published on Feb 11, 2022
Dahua LPR ITC237-PW6M-IR(L) Guideline
  • Published on Feb 11, 2022
Description This guide will show simply how to add DVR cameras to NVR. It allows you to view and record all DVR channels on NVR.
  • Published on Feb 11, 2022
Download and install Toolbox from the link . Install ConfigTool from Toolbox. Run ConfigTool. Click on Search Setting. Enter the password of the IP camera. Click OK. Click on IP Modificatio...
  • Published on Feb 11, 2022
Download and install Toolbox from the link . Install ConfigTool from Toolbox. Run ConfigTool. Check the IP camera and click Initialize. Click Initialize. Set a New Password for the IP Camera. ...
  • Published on Feb 11, 2022
Introduction This guide shows how to adjust the PC network to reach the local devices like IPC or Access Control panel. Step1 Right Click and Open Network&Internet Settings Step2 Network and Sharing Center Step3 Choose your networ...
  • Updated on Feb 12, 2022
  • Published on Feb 11, 2022
Introduction This guide will show you how to update IPC firmware from a PC remotly. Prerequestites SmartPSS software Target Device have been added. Step1 Open SmartPSS -> Device Config ->Link to Web Step2 Login to ...
  • Updated on Feb 12, 2022
  • Published on Feb 11, 2022
Step 1 . In Access interface, you can click on the left to enter User Management interface, to manage all users. Step 2 .Set Card Type If card type and card reader do not match, then you cannot read card no.! In User Management in...
  • Updated on Feb 11, 2022
  • Published on Feb 11, 2022
Step 1 Press [#] + admin password, and press [#] again to enter the main menu. Step 2 Press [1] + [#] key to add a user Add user ID (1 to 8 digits). Input ID and end up with [#] key(If the user ID exists already, it will fail to be added) ...
  • Published on Feb 11, 2022
Step 1:Connect a POE switch to the lan port of the recorder. See Picture below Step2. Connect your cameras to the POE switch. The go to main menu -> camera -> camera registration. Click Device Search and then click Uninitialized. Devic...
  • Published on Feb 11, 2022
Step 1 On the live view, right click and choose PTZ. Step 2 On the Expanded PTZ Control Panel, click The MENU OPERATION interface is displayed. See Below Step 3 Click Enter. The OSD menu is displayed. See Figure Step 4 On the MENU OPE...
  • Published on Feb 11, 2022
Step1. On the live view, page right-clicks to call the main menu. step2. choose Preview mode, then choose Ai mode to enable it. The AI capture will show on the right.
  • Updated on Nov 23, 2022
  • Published on Feb 11, 2022
Description When a face is detected in the area, the system compares the face image captured with faces added to the face database and can link to an alarm output based on the comparison result. Initial Setup for Recorder Enter the Main Me...
  • Published on Feb 11, 2022
Step 1 Select Main Menu > CAMERA > OVERLAY > Overlay. The Overlay interface is displayed. Step 2 Configure the settings for the text overlay parameters. Step 3 Click Apply to complete the settings
  • Published on Feb 11, 2022
Select Main Menu > AI > Parameters > IVS. Select the Channel number to configure from the Channel list Click Add. A new line of rule will be created. Select the Type on the rule line. Click Draw. ...
  • Updated on Feb 11, 2022
  • Published on Feb 11, 2022
You can configure the channel type as Analog or IP channel. Step 1 Select Main Menu > CAMERA > CHANNEL TYPE. The CHANNEL TYPE interface is displayed. Step 2 Configure the channels. You can enable the IP channels by disabling th...
  • Updated on Feb 12, 2022
  • Published on Feb 12, 2022
You can configure a tour of selected channels to repeat playing videos. The videos display in turn according to the channel group configured in tour settings. The system displays one channel group for a certain period and then automatically changes ...
  • Published on Feb 12, 2022
Description This is a guide for How to Add Dahua DVR or NVR. Prerequisites DSS Express Connected network NVR/DVR 1. Go to Homepage➞Management ➞ Device Click Add Select the Register Mode (IP Address or SN) Ente...
  • Published on Feb 12, 2022
Description This guide shows you how to enable the 2nd monitor and set up the view type for it. Setup Step 1 Select Main Menu > DISPLAY > Display. The DISPLAY interface is displayed. To use the 2nd output, we need to enable extra Scre...
  • Published on Feb 12, 2022
Description This guide will show you how to upgrade the firmware of a device using VDPConfig Prerequisites Windows PC. Dahua Toolbox VDP Config Dahua video intercom device on the same LAN as the PC Step by Step Instructions Ope...
  • Updated on Mar 15, 2022
  • Published on Mar 8, 2022
Instruction Download SmartPSS for MAC 2.Go to downloads and select the SmartPSS file. 3. Highlight SmartPSS ➞ Right Click and a sub menu will show ➞ Click on Open. 4. The MAC OSx security will block the installation of the ...
  • Published on Mar 8, 2022
Instructions Double click on the installer to use the archive Utility Now go to your MAC settings and click on Security and Privacy A pop up will come up, click on Open SmartPSS will then be extracted to your de...
  • Updated on Jun 15, 2022
  • Published on Jun 8, 2022
Description Disclaimer - Auto Tracking and Panoramic view will not work simultaneously PTZ tracking is an innovative feature that transforms manually controlled PTZ cameras into automated tracking systems that keep an moving object in focus ...
  • Updated on Jun 21, 2022
  • Published on Jun 21, 2022
To Add a Dahua Camera to a Hikvision NVR NOTE: ONVIF must be enabled on the Dahua camera before trying to add the device to a Hikvision recorder. log in to the NVR web UI and hit on the Configuration Tap --> Camera Management . ...
  • Updated on Jul 18, 2022
  • Published on Jul 18, 2022
Prerequisites A Gmail account An email address to send the notifications to A Dahua NVR Step by Step Instructions Log into the web interface of the NVR then select Setting at the top left. Select Network from the drop-down ...
  • Published on Jul 19, 2022
Explanation Here we will explain how to connect a Dahua IP camera to a Hikvision NVR. Step 1: Connect Dahua IP Camera to NVR For a Dahua IP Camera, you’re going to be configuring your camera using the Config tool (you can download it on the ...
  • Updated on Dec 15, 2022
  • Published on Dec 15, 2022
Description There are multiple options for configuring how the PTZ will function. See below for the different types and how to configure them via Camera webpage or in NVR local interface. Preset - A saved position. The cameras Pan (Left/Ri...
  • Published on Jul 24, 2023
Prerequisites Dahua-Toolbox Icon.png Dahua Toolbox installed Windows PC. Dahua Devices on the same LAN as the PC for using the ConfigTool. Step by Step Instructions From the Dahua ToolBox, open the ConfigTool. Upon opening the Conf...