Parameter List & Descriptions

Prev Next

Compatible model: ADC-AI- S300

Note: All values and settings must comply with applicable national and provincial/state standards, including local building codes and accessibility regulations.

Parameter table

Index

Parameter

Description

Function Behavior / Effect of Adjustment

Value

Default

01

Overload

Obstacle Detection Sensitivity

Lower values increase sensitivity, making the door stop or reverse more easily when resistance is detected during the opening cycle. Higher values decrease sensitivity, better handling wind or pressure but may delay obstacle detection.

60-80

70

02

Act Delay

Delay between trigger and activation of ADO (10th of Second)

Shorter delays cause the door to activate more quickly after receiving a trigger.

Longer delays introduce a pause before activation. Increase delay if activation button is far from the door.

0-99

0

03

Backcheck Speed

Speed of the door at last 20 degrees

Controls the door speed during the final 20° of opening.

The higher the value, the faster the speed.

1-60

25

04

Holding Time

Time (in seconds) that the door will stay open when reaching the backcheck zone

Longer times accommodate slower users or equipment.

0-99

10

05

Opening Speed

Door opening speed

Adjusts the speed at which the door opens.

The higher the value the faster the speed.

1-99

50

06

Closing Speed

Door closing speed

Adjusts the speed at which the door closes.

The higher the value the faster the speed.

1-99

30

07

Latch Speed

Door latching speed

Controls door speed during the final latching phase.

The higher the value the faster the speed.

1-99

10

08

Control Mode

1 = Regular,

2 = Unlocked washroom,

3 = Access control,

4 = Locked washroom

Selects the door’s operational logic.

Each mode alters how the door responds to inputs and security features.

1-4

1

09

Sensor Cfg.

Safety sensor configuration selection

Specifies the number of connected safety sensors.

A setting of 0 means no sensor is used.

0-8

0

10

Stop Speed

The speed of the door once presence detected via sensor on swing side

Works only if additional sensors are being used.

1-60

10

11

Power Close

Powered closing of door to positive latch (toggle)

0 = OFF,

1 = ON

Enables powered closing to fully latch the door.

Useful in high-pressure environments or where positive latching is required.

0-1

0

12

Power Cls Spd

Power closing force adjustment

Adjusts the force applied during power closing.

Higher values provide stronger force to overcome resistance.

1-35

20

13

Powr Cls Angle

Power Closing engage angle

Sets the door angle at which power closing begins.

Larger angles start power closing earlier in the cycle.

10-45

15

14

Closing Time

Countown (in seconds) to full close

Sets the countdown duration for the door to fully close.

0-50

50

15

Opening Time

Countdown (in seconds) to full open

Sets the countdown duration for the door to fully open.

0-50

50

16

Latch Time

Countdown (in seconds) in latch cycle

Sets the countdown duration during the latch phase.

When value is 0, allows for instant locking, use 2-8 for normal door functions, lower the value the earlier the locking.

1-8

2

17

Latch Angle

Latch cycle angle

Sets the angle at which the door will begin to slow before fully closing the door.

Wider angles provide more control and adjustment in the final closing phase.

1-45

20

18

Decel Angle

Backcheck start angle

Sets the angle at which backcheck (deceleration) begins.
Higher angles trigger deceleration earlier to soften impact.

20-110

80

19

Preload Time

Pull time door before opening to release pressure (10th of second)

Sets the duration the door pulls in before opening to relieve pressure.

Adjust the value if there’s trouble with an electric strike.

0-50

0

20

Preload Spd

Pull force of door before opening to release pressure

Adjusts the force of the preload pull before opening.
Higher values increase pulling force to overcome pressure seals.

Fixed

50

21

Wind Brake

Turn ON/OFF wind break feature

0 = OFF,

1 = ON

When enabled, the wind brake helps resist wind pressure during door opening, improving stability in windy environments.

Usage Note:
When manually opening the door with wind brake enabled, continue pushing the door until it is fully open.
Avoid a quick push-and-release action, as this may cause the system to detect a false obstruction due to the encoder stopping abruptly.

0-1

0

22

Wbrake Speed

Wind buffer force

Sets the strength of the wind buffer.
Lower values apply greater resistance against wind.

1-99

10

23

Wbrake Angle

Wind buffer engage angle

Defines the door angle where wind buffer engages.
Adjust to tailor wind resistance response timing.

25-110

60

24

Wbrake Sens

Wind buffer engage sensitivity

Adjusts the sensitivity for wind buffer activation.
Higher values increase responsiveness to light wind force.

1-99

20

25

Fire Al Mode

0 = Smoke evacuation mode (door opens),
1 = NFPA80 standard (disables ADO on fire alarm)

Sets behavior in fire alarm situations.

0-1

0

26

Easy Open

0 = Heavy,

1 = Standard 15lbs,

2 = Light 5lbs

This refers to pounds of force needed to push the door manually.

0-2

1

27

Quick Open

0 = Slow ramp from full closed,

1 = Standard ramp,

2 = Quick “kick-out” for fast opening

Sets acceleration profile from closed position.

0-2

1

28

Reactivate

0 = No reactivation until fully closed,

1 = Allows reopening during closing,

2 = Touch-reverse on closing obstruction

Sets door behavior when a second open signal is received during the closing cycle.

0-2

1

29

Factory Test

0 = Normal operating state, no reset action performed,

1 & 2 = Developer use only (for testing and debugging),

3 = Perform factory reset

Set the value to 3 to clear all user parameters and reboot the system.

0-3

0